The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.
|Genre:||Health and Food|
|Published (Last):||21 April 2008|
|PDF File Size:||8.52 Mb|
|ePub File Size:||14.81 Mb|
|Price:||Free* [*Free Regsitration Required]|
By programming data ” 1A ” into another of the 0V multi-function parameters, the corresponding multi-function input terminal becomes the Time Selection 2 input.
Elapsed Timer Selection Factory setting: With full scale input, adjust Gain H 3 – 0 2 magnetei H 3 – 0 6 setting until an output of The addition of Integral Time will cause the steady-state error to approach zero. With no input, adjust Bias H 3 – 0 3 or H 3 – 0 7 setting until an output of 0.
Setting b to ” 0 ” may correct a runaway condition. Gain and bias for terminal 14 are set by H 3 – 0 2 and H 3 – 0 3respectively. If only a remote Manual Speed pot 1RH is magetek, 3SS is not needed; in that case, a jumper must be added between terminals 5 and A A thru A 1 b b b 1 1 0 5.
If Stop is initiated while the HOLD command is present, the prohibit state is cancelled and the system enters stop operation. Customer to magnegek terminal 6.
Stall Prevention Level During Accel This parameter determines the actual drive output current level during an acceleration condition. For further details magnrtek dynamic braking operation, see the instruction sheet shipped with dynamic braking components. Image not available Photos not available for this variation.
Yaskawa Magnetek GPD 515 Gpd515c-b003 Spec 40p71f 2 HP Drive 3ph 380-460v
The drive retains the last four faults and the operating conditions when the last fault occurred. Step A Display the frequency reference that was present when nagnetek fault occurred. Depending on the control wiring configuration and the multi-step mode chosen, the motor can be operated at up to nine different speeds. Want it shipped today?
Timer Input Function H 2 – 0 1: Motor Rated Current Factory setting: On units equipped with bypass, it may be wired to the primary side of the circuit breaker and mounted to the bypass panel or sidewall. The figures following the magbetek show how each setting configures the analog input.
Yaskawa / Magnetek GPD 515/G5 Sine-Coded Pulse Width Modulated AC Motor Drive
Report item – opens in a new window or tab. Learn More – opens in a new window or tab Returns: This connection can be made according to Figure Sets the output frequency at leveling speed.
When applying a Variable. The following information used in the calculation formulas is usually magnete, on the motor nameplate. Good morning, We are very happy with your service, delivery, and purchase. See all medproequip has no other items for sale. Modify this parameter to obtain desired leveling speed. See Table A Range: Speed pot or VDC signal only: Set the meter at the X1 range.
GPD /G5 Drive Technical Manual |
Will usually ship within 2 business days of receiving cleared payment – opens in a new window or tab. Enabled – Output magnettek limit and slip compensation are enabled above base speed 1 0, 1 0 — — A A 5. I found your company on line ,the sinumeric PCU50 was an obsolete part from the machine manufacturer so we where dead in the waterafter speaking to Joe he was very helpful and knowledgeable, he knew what we needed and the part was in stock newbut he also gave me some more economic options to choose fromi opted for the new unit and they magnrtek it the same day.
LED lights when drive is controlling motor speed. In this More information. Inverted A A A 5. For parts or not working: If the output frequency is greater than or equal to the C 1 – 1 1 frequency, the C 1 – 0 1 and C 1 – 0 2 times are used. Same Day Shipping Weight: This item will ship to United Statesbut the seller has not specified shipping options.
During tuning, the following message will appear: