LCD PROJECTION TELEVISION. KDFE LCD TV pdf manual download. Also for: Kdfe, Kdfe, Kdfe, Kdfe, Kdfe Sony KDFE – TV – Service Manual — Free Service Manuals. Download Manual for Model KDFE SONY LCD PROJECTION PartsDirect has parts, manuals & part diagrams for all types of repair.

Author: Vulrajas Zulkijinn
Country: India
Language: English (Spanish)
Genre: Relationship
Published (Last): 6 September 2014
Pages: 133
PDF File Size: 7.67 Mb
ePub File Size: 17.27 Mb
ISBN: 773-4-97900-599-6
Downloads: 53387
Price: Free* [*Free Regsitration Required]
Uploader: Yora

To change the Data Value, press 0 or 0 on the Remote Commander. If the lamp is not securely reattached, the self-diagnostic function may be triggered and the POWER indicator flashes three times see page Comments 0 No comments yet.

Page Put the outside lamp cover back in its place. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Lamp Connector and T2 Board Removal 19 1- Gently pull the K Board out of the Main Bracket.

To maintain the quality of your viewing experience, Sony recommends servide you replace the Lamp 1 after approximately 8, hours of use the TV will display a message servicee you to replace the lamp ; 2 when the screen becomes dark or the color looks unusual; or 3 when the LAMP indicator on the front of the TV flashes.

Expect some delay when ordering these components. Avoid touching the front glass of a new lamp or the glass of the lamp receptacle. Got it, continue to print. Wire Should be pulled so that there is no excess wire. Ne les remplacer que par une piece portant le numero speclfie. The Lamp Hours and Panel Hours are shown in hexadecimal format. Put the outside lamp cover back in its place.



Voltage variations may be noted due to normal production tolerances. Actual measured value may be differentsignal path. Wait approximately 5 seconds until the data value is reset to 0.

Remove as much slack out of wire before dressing it to the wire holder. All kdg50e2000 are in V. Consult your Sony dealer for a Sony XL replacement lamp. Accessing Service Adjustment Mode 49 See below to see which wires are dressed to each wire pin holder 1. By submitting a comment, you are declaring that you agree manuql these rules:.

If the retaining screw is to be used as your earth ground, verify that it serice at ground by measuring the resistance between it and a cold-water pipe with an ohmmeter. A battery-operated AC milliampmeter. The components identified by shading and mark are critical for safety. Table of Contents Add to my manuals Add. A and other sservice. Be absolutely certain that you have replaced all the insulators. Do not shake the lamp. Press the following buttons on the Remote Commander within a second of each other: Point them out to the customer and recommend their replacement.

To print the manual completely, please, download it. When removing the Screen Frame Assembly be sure to clean the Mirror and Diffusion Plate s to remove any dust particles. Never put janual used lamp into a plastic bag. Use of any other lamp may mwnual the TV. To remove the speakers, remove 2 screws and release the speaker wires.


Speaker Conn Assy 2. These terms and conditions are subject to change at any time and without notice. Gently pull the Screen Frame Assembly forward. Replacing The Lamp Lamp maintains its brightness will vary depending upon your usage and environmental conditions. To avoid being burned, do not touch the lamp receptacle once the lamp has been removed.

Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony.

Sony KDF-46E2000 Service Manual

After completing all adjustments turn the set off with the Remote Commander and WAIT for the fans to turn off before proceeding to the next step. Wait 2 minutes before restarting the set to allow the fans to completely shut down or the Service Menu will appear on the screen. Proceed to Viewing the Self-Diagnostic Errors. You acknowledge that all comments express the views and opinions of the original author and not those wervice the administrator.

Disposal of this product may be regulated if sold in the United States. To reset the Lamp time, press 0 to change the data value to 1.

Turn the fan cover over to remove the T 1 Board and Kdc50e2000 Board.

Free Service Manuals

Press 0 to change the data value to 1. Replace only with part number specified.

TV must be in standby mode. Ne les B G with part number specified.