View and Download DSC PC installation manual online. v DLS or higher. PC Control DSC PC DSC PC – V Manual 34 pages. For programming instructions, see the Installation Manual, Section 3, “How to Program”. SYSTEM AREA [0] Clear Display [2] Change Case [4] Cancel and Exit. The user may find the following booklet prepared by the FCC helpful: Your DSC security equipment has been designed to give you the greatest possible .. [0] Quick Arm (1) Quick Exit (2] Auto Arm Control [3] Keypad Setup.

Author: Zolomuro Yolmaran
Country: Estonia
Language: English (Spanish)
Genre: Career
Published (Last): 4 June 2009
Pages: 62
PDF File Size: 17.41 Mb
ePub File Size: 9.31 Mb
ISBN: 917-2-48660-733-3
Downloads: 76333
Price: Free* [*Free Regsitration Required]
Uploader: Durisar

S e ction 2: Use codes should be given to casual users. Any zone from zone to on the Programming and enter ref []. UL Listed Commercial and Residential Installations Control of the Protected Premises In order to have a UL Certificated system the protected area is to be The installation requirements listed below must be met for the fol- under the responsibility of one ownership and management i.

DSC PC4020 Installation Manual

The smoke detectors may have been improperly installed or ber or serial number; To disable communications, enter reference number []. By default, the Comm Enabled toggle option is on to enable communications. The mission would look similar to this example: Reporting Code Code Sent When Ascii Characters A pp e n dix C: Page 34 TLM and Alarm 14 This output will activate when any zone tamper alarm The output will activate when a telephone line trouble is occurs on the selected partitions.


All circuits are classified UL installation power limited except for the battery leads which are not power limited. This notice manuql to be framed and mounted adjacent to the control unit or the keypad at the main entrance. System Programming S e c tio n 1 0: Power for the 4-wire smoke detectors may be derived from cated as a Common Ground Fault Trouble.

Valid entries for the Disarm Delay duration are from minutes. Links Communications S e mannual t i o n 1 5: Enter text from picture: Prior to the final verification of sys Table of Contents Add to my manuals Add.

Installation and Wiring 9. Partitions And Zones S e c t i o n 5: Page 4 Section By pressing ‘print’ button you will print only current page.

Don’t show me this message again. Don’t have an account? By pressing ‘print’ button you will print only current page.


If enabled, all access codes will be 6-dig- its, except for the panel ID code and Downloading access code. Each option is described later in this manual in the specified sections.

Once the digit is entered, the control panel will automatically return to the decimal pro- gramming mode. Adding Zones To Partitions 1.

DSC MAXSYS PC4020 Installation Manual

In order for an access code to function, you must program which partitions the code will be active on. Page 40 AC Status 57 Program command output labels in this section.

  IEC 61196 PDF

Each LED assembly draws up to 20mA of current.

Maxsys pccfMaxsys pc To print the manual completely, please, download it. If enabled, the panel will follow the dou- ble call procedure. Addressable Loop Response Time Addressable Loop Wiring The overall system response time for devices on the AML devices home-run, connected in a loop depends on how many devices are on each loop.

Installer And Access Codes S e c t i o n 7: Openings and closings Event scheduling allows for a variety of timed events to occur on specific dates and at specific times. Fire zone program- ming is the same as burglary zone programming.

DSC PC v Program Sheet

Do not pro- gram codes that can be easily guessed. Introduction Page 6 – Section 2: To print the manual completely, please, download it. For You can enable the lamp test feature for each PC mod- more information regarding this key, see the PC Instal- ule when it is enrolled refer to the PC Installation lation Manual Section 6. Do not use this format with Hz ID. It will remain active present and an alarm occurs on any of the selected parti- until the partition is disarmed alarm silenced or the bell tions.

The default setting is Installation And Wiring S e ction 2: