ASTM Standards. ASTM F ASTM F – Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within. Consult Labthink Instruments Co., Ltd.’s High Pressure Leak Tester for Package ASTM F, ASTM F brochure on DirectIndustry. Page: 1/4. More help in interpreting the results can be found in ASTM F Inflation Seal Strength Testing (ASTM F and F), including burst, creep and creep-to-.

Author: Shakale Shaktigrel
Country: Reunion
Language: English (Spanish)
Genre: Education
Published (Last): 12 August 2017
Pages: 199
PDF File Size: 19.58 Mb
ePub File Size: 8.18 Mb
ISBN: 286-9-80613-960-9
Downloads: 79887
Price: Free* [*Free Regsitration Required]
Uploader: Ter

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures.

Product List | RDM Test Equipment | Assured Quality Testing Solutions

By placing the package within restraining plates during pressurization, aatm dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed.

In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package. See Appendix X4 for information. The Online Industrial Exhibition. This allows the test to have a higher probability of detecting the weakest area of the d2054 and provide a measurement of the pressure required to “burst” open the package.

MFY Leak Tester is used to look for pin holes in bags that hold calibration solutions for medical instruments.

Link to Active This link will always route to the current Active version of the standard. Seal Strength system to test 3 sides seal bags. This test method cannot provide a measure of package seal uniformity.

Typical parameters can include, but are not limited to the package size, material, type and configuration of aztm, rate of air flow into the package, pressure detection sensing mechanism and sensitivity machine response to pressure dropposition of test article, rigidity of restraining plates, and distance between restraining plates. See Appendix X4 for information.

  LIBRO BURGUES GENTILHOMBRE PDF

Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the atm maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal. MFY leak detector for our g2054 packaging. COF Inclined Plane Tester Measure the static coefficient of friction of various materials using a variable inclined plane and a sliding block. Oxygen Permeability Tester to test containers.

Labthink RT rub tester to test on flexo printing. This standard does not purport to address all of the safety concerns, if any, associated with its use.

Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal. Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal.

Astj test method also cannot provide an evaluation of overall package integrity or the burst strength of areas of the package that contact the surface of the restraining plates used. Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures.

Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses. Flexible packages, aseptic packages, various plastic pilfer-proof closures, flexible tubes, caps and other materials. Active view current version of standard. Reference Appendix X3 for further information regarding calculation of stress f20544 and structural design considerations.

This test method should be combined with other methods of evaluating overall package integrity, uniformity of the package seal, or opening functionality, if so required. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This test method provides an indicator of the burst strength of a package, where the burst will normally occur in one or more areas of the seal.

  KARLFRIED GRAF DRCKHEIM PDF

An indicator of the minimum burst strength may be of importance to the package manufacturer and end user in ensuring adequate package integrity. Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses.

ASTM F2054

Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations. See Appendix X2 for further information. Link to Active This link will always route to the current Active version of the standard. In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package.

FT-F1 Fogging tester to to test for fogging on upholstery material and time frame for testing. Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal. By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed.

Labthink provides COF Tester for coef. Specifications Test Range Contact: Three Tests in one instrument High Pressure Leak tester With various accessories for tests of different packages Applications: Vacuum Leak Tester for bottles for food, chemical and pharmaceutical applications.

Pressure differentials may occur during such processes as sterilization and transportation.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Thickness micron testing equipment with Resolution 0. Tensile Tester for both compression and tensile, with loads typically N.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Historical Version s – view previous versions of standard.