Add Attachments to Content Item ‘ASTM D Glass Transition Temperature ( DMA Tg) of Polymer Matrix Composites by Dynamic Mechanical Analysis (DMA) . ASTM D Glass Transition Temperature (DMA Tg) of Polymer ASTM D has become a widely used test standard in many companies due to. ASTM D用DMA测试Tg_能源/化工_工程科技_专业资料。Designation: D – 07?1 Standard Test Method for Glass Transition.

Author: Bak Aracage
Country: Greece
Language: English (Spanish)
Genre: Environment
Published (Last): 18 April 2011
Pages: 383
PDF File Size: 4.97 Mb
ePub File Size: 20.32 Mb
ISBN: 232-7-83796-843-4
Downloads: 12200
Price: Free* [*Free Regsitration Required]
Uploader: Nikomi

Other materials, such as neat resin, may require non-standard deviations from this test method to achieve meaningful results. The values given in parentheses are non-standard mathematical conversions to common units that are provided for information only.

Sampling and Test Specimens 8. Link to Active This link will always route to the current Active version of the standard.

During the glass transition, the storage modulus of the composite material is signi? Summary of Test Method 4.

Determination zstm Report of Procedures. The maximum time between cure lamination and testing shall be 30 days, after which, prior to testing, specimens shall be oven-dried in accordance with Interpretation of Results The peak temperature of the tangent delta curve Tt is identi?

Any deviations from the standard orientation shall be reported and the test results noted as non-standard. Depending on the analyzer, typical specimen size can range from 56 6 4 3 12 6 1 3 2.


Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. If the two tangent lines are constructed from temperatures too close to the transition, the intersection is depicted as shown in Fig. D Practice for Plastics: Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

Weigh the specimen after the test to the nearest milligram 0. The span-to-depth ratio, astmm orientation, and ply stacking sequence of a specimen with respect to the testing?

ASTM D7028 – 07(2015)

Work Item s – proposed revisions of this standard. A number in parentheses indicates the year of last reapproval. Referenced Documents purchase separately The documents d708 below are referenced within the subject standard but are not provided as part of the standard.

The materials listed in Table 1 are de?

Should the results be retained, then these conditions shall be described in the test report. A new or spare specimen shall be prepared from the same material package and tested to replace any specimens rejected per this paragraph. Precision and Bias 4 It is widely known that heat transfer limitations are more pronounced in DMA apparatus compared to other thermal analysis techniques, such as differential scanning calorimetry DSC and thermomechanical analysis TMA.


The conditioned specimens shall be tested within 30 minutes after removal from the conditioning chamber, or stored in sealed MIL-PRF or equivalent aluminized bag until test. Strains of less than 0. Your comments will receive astk consideration at a meeting of the responsible technical committee, which you may attend. Test Method E speci? If the testing is part of a designed experiment, other sampling techniques may be used if described in the test plan.

ASTM D用DMA测试Tg_百度文库

This temperature is designated as TB. Therefore, it is recommended that the test specimens should be weighed before axtm after DMA Tg testing to quantify the moisture change in the specimen resulting from the DMA Tg test.

Any deviations from this heating rate shall be noted in the report and the result shall be reported as non-standard.

Measure the specimen length to 0. The values given in parentheses are non-standard mathematical conversions to common units that are provided for information only. For some types of dynamic mechanical analyzers, a purge gas?