GE Healthcare c Anesthesia Machine Technical Reference Manual Software Revision 1.x Approved −12−9 EET Junmin Ji (Rick) M c Product Data Sheet – GE Healthcare c Familiar, reliable, GE – with over years experience in anesthesia and quality leadership? 53 cm/21 in Depth: 40 cm/16 in Side of machine: cm/45 in Height: The c is the ideal solution for customers seeking an affordable, reliable and easy-to-use anaesthesia system. The c is designed and manufactured in.

Author: Nitaxe Galmaran
Country: Bahamas
Language: English (Spanish)
Genre: Marketing
Published (Last): 24 April 2012
Pages: 134
PDF File Size: 18.36 Mb
ePub File Size: 11.1 Mb
ISBN: 119-1-81437-765-2
Downloads: 69542
Price: Free* [*Free Regsitration Required]
Uploader: Mezigor

Connect the pipeline supplies one at a time and ensure that the corresponding gauge indicates pipeline pressure. Mississauga, Ontario Australia Pty. Disconnect the harness D to the LCD display. To reassemble, perform the previous steps in reverse order. For an N2O manifold, you will have to carefully apply pressure at the outlet of the manifold — with a syringe for example — to gently force the check valve out of the manifold.

MOPV pressure relief valve test Section 6. Read completely through each step in every procedure before starting the procedure; any exceptions may result in machkne failure to properly and safely complete the attempted procedure.

All flow data uses a new filter. Remove the patient Y-piece from the bag port handle. Annual Turnover More than Rs. It is piloted closed during mavhine and remains closed until the bellows is refilled during exhalation. Power cord plugged into live receptacle; AC Inlet 2. Are Plimit and other controls Middle The ventilator cycles to set correctly?

  CONFESSOR TERRY GOODKIND FREE PDF

Move the display slightly right to disengage the mounting pins.

Multipurpose Anaesthesia Machine- 9100C

Log In Sign Up. Disconnect the high-pressure cylinder gauge fitting. Middle What is the O2 flow? Is the O2 flow sufficient? Set the system switch to Standby. Set the fresh gas or O2 flow to 0.

Anesthesia Delivery

Cylinder supplies could be depleted, leaving an insufficient reserve supply in case of pipeline failure. Push the new check valve into the opening, using the same thin tool. Is the limit machiine correctly? On the Function Upgrade menu Section 4.

c NXT | GE Healthcare

The apnea alarm occurs after 15 seconds. To adjust the cylinder regulators, follow the procedure in Section 5. Pull abesthesia knob E off the shaft of the encoder F. Pull the O2 supply switch out of the manifold.

Breathing circuit parameters Compliance: Verify that T-handles are tight. The large port is the port closest to the patient circuit Y- piece Section 2. Cylinder gaskets Use a leak detector or Snoop to check for source of leak. To replace the switch, reassemble in reverse order.

Place the new APL valve into position with the setting indicator facing to Front the front of the machine. Remove the bellows assembly, then connect mmachine calibration fixture A to the drive gas outlet.

  ANALISI MATEMATICA 1 BRAMANTI PAGANI SALSA ZANICHELLI PDF

Open the cylinder yokes. Gas flows from the bellows, through the absorber, the EZchange, and through a unidirectional valve inspiratory check valve to the patient. Active AGSS systems with a Illustrations in this manual anestnesia not represent all configurations of the product.

Note This is not the actual calibration of those components. Inspiratory flow valve Flow control tests Section 3. O2 flush stuck on? Disconnect the tubing from the manifold outlet s. Use the following tightening procedure whenever you are replacing a cylinder supply or pressure tube fittings a cylinder pressure gauge. Install a new cylinder gasket and do this step again. Ensure that the bellows is completely collapsed.

Disconnect the cable, replace the display module and reassembly in reverse order. This Check tubing connections. This alarm is suspended for 9 Adjust control settings. Therefore, GE agrees to make available Interfacing information and data, as described in the Interfacing Commitment, between the following product combinations: Verify that parts are free of dust and dirt.